Mesh belt dryer, high temperature mesh belt dryer, stainless steel mesh belt dryer, box-type mesh belt dryer, multi-layer mesh belt dryer
High-efficiency stainless steel mesh belt dryer manufactured by Linyi Dahua Machinery Factory. Mesh belt dryer is used for drying and drying various shapes of briquettes, coke powder pellets and other non-ferrous and black metallurgical ore powder pellets, scale, sludge, returned slag ore pellets, etc. produced by the briquetting machine. Sintering (℃ high temperature), wide application, high efficiency, energy saving and other advantages. The length of the machine can be long or short, completely according to the user's needs. It is suitable for use in production lines with a wide surface area and an output of 1,000,000,000,000,000 tons/hour. This machine is a high-temperature dryer, and the internal temperature is around ℃. Walking time minutes. Easy to operate and maintain.
Linyi Dahua Machinery Factory Mesh Belt Dryer Features:
High drying intensity. Since the material is highly dispersed in the air flow, the entire surface of the particles is actively used as an effective area for drying. >
, short drying time>
, the air flow dryer has a simple structure, small footprint, and is easy to build and maintain. >
, large processing capacity and high thermal efficiency. Thermal efficiency is achieved when drying unbound water. >
The dryer achieves zero horizontal thrust r, which greatly reduces the wear of the supporting wheel, and the cylinder runs smoothly and reliably>
The dryer adopts an aligning support The wheel device r makes the cooperation between the supporting wheel and the rolling ring always in linear contact, thus greatly reducing wear and power loss.
The box dryer is suitable for sheets, strips and granules with good air permeability. Drying of shaped materials. It has unique advantages for materials that require low drying temperature and long drying time.
The mesh belt dryer is a batch and continuous production drying equipment. The main heating methods include electric heating, steam heating, and hot air heating. The main principle is to spread the materials evenly on the mesh belt. The mesh belt is made of steel wire mesh belt and is dragged by the transmission device to move back and forth in the dryer. The drying section is composed of several units, and the hot air in each unit circulates independently, among which Part of the exhaust gas is discharged by a special dehumidification fan, and the exhaust gas volume of each unit is controlled by a regulating valve. In the upper circulation unit, 1. Mesh belt dryer (mesh belt dryer) function: The mesh belt dryer passes the materials to be processed through appropriate spreading mechanisms, such as star distributors, swing belts, crushers, etc. machine or granulator, distributed on a conveyor belt. The conveyor belt passes through a channel composed of one or several heating units. Each heating unit is equipped with an air heating and circulation system. Each channel has one or several dehumidification systems. When the conveyor belt passes, the hot air passes through the materials on the conveyor belt from top to bottom or from bottom to top, so that the materials can be dried evenly. 2. Mesh belt dryer (mesh belt dryer) product features: The mesh belt dryer (mesh belt dryer) can adjust the air volume, heating temperature, material residence time and feeding speed to achieve the best results. drying effect. The air from the circulation fan enters the lower chamber of the unit through the side air duct. The airflow is heated upward through the heat exchanger and distributed by the distributor. It blows towards the mesh belt into a jet stream, passes through the material and then enters the upper chamber. The drying process is where the hot air flow passes through the material layer to complete the heat and mass transfer process. The upper chamber is connected to the fan inlet by an air duct. Most of the air circulates, and part of the gas with lower temperature and higher moisture content is discharged as waste gas through the moisture discharge pipe, regulating valve, and moisture jump fan. In the lower circulation unit, the air from the circulation fan first enters the upper chamber, is heated downward by the heat exchanger, and passes through the material layer into the lower chamber. The lower chamber is connected to the fan inlet by the side air duct and return air duct, and most of the gas circulates , part of it is discharged. The upper and lower circulation units can be flexibly equipped according to user needs, and the number of units can also be selected as needed. In order to save space, the dryer can be made into a multi-layer type. Common ones include two chambers with three layers, two chambers with five layers, length, effective width...
If you need help, please call: Linyi Hedong District Dahua Machinery Factory is always ready to provide you with better products and the most economical and reasonable solutions. Our technical experts are always available to provide you with technical assistance and hope to work with you. You establish a long-term cooperative relationship that pursues higher value! Our factory has been a member of Ahli’s Integrity Pass for many years and has a high degree of credibility!
Stainless steel mesh belt type multi-layer dryer price